Since you have Waits, there's a good picture of a set on page 13 of the ASR section. Under the heading "British Ever-Ready Sets" in the first column is a set with a stropper from the 1930's (the ivory bakelite case on the right). Waits doesn't identify it as a Streamline for some reason. At the bottom of the right column on the same page is an "Ambassador" set, apparently from the 1950's. I've read somewhere that there was a period between the two sets when the Streamline wasn't being produced.
Someone more knowledgeable will be along shortly to clarify, no doubt.
I've got a cased Streamline, just the razor no stropping set up. Can't find a picture but I'm sure there'll be a few posters here with a few. If I may here's a link to a B&B thread with loads of pictures. Mine's identical to post No 4. It's the emperor of flip top SEs. Built like a tank, plated like a WMD. Superb machine.
Post by HoosierTrooper on Mar 17, 2012 7:26:46 GMT -6
Here's mine and it is a fantastic razor, beautifully finished and an absolute joy to shave with. I actually used it this morning with a Gem Blue Star blade and vintage Colgate Cup soap so your thread was quite timely.
I've read that they were made in the 30's and then in the 50's and if what I've read is correct mine is the older one based on the drainage holes in the bottom plate.
Post by HoosierTrooper on Mar 17, 2012 9:42:37 GMT -6
I had it wrong, mine is actually a new version if what I've read is correct. The newer models have two small drainage holes and holes in between the teeth on the guard, the older ones have two large holes in the bottom plate and none in the guard bar.
You can see the main drainage holes and the ones between the teeth in the shadow.
Here's the older style (excuse the soap residue, I've been using it):
Edit: I just looked at the picture and it looks like my poor Streamline is brassing like the devil. It is a trick of the light and highlights my poor photographic skills. The plating is rock solid. The razor is a tank.
Last Edit: Mar 17, 2012 12:30:37 GMT -6 by Deleted
I'd have to disagree with Shadowsdad. I think they are pretty rare. It took me a while to find one and I didn't care about the price either. I had to outbid several serious SE collectors. Prices are going northwards a bit but still less than your average user grade Fatboy. You should be able to pick one up for $50-$60.
The equivalent GEM Jewel is one you see even less in my experience.
9nein9: To like or not to like the like button? That is the question. Our society thrives off the like button it seems . I'm not sure if I like it or I don't like it.Just kind of got used to it .
Dec 15, 2019 20:32:06 GMT -6
carlfrommo: Hey guys. Last minute question here. What shot size should I use for flying reindeer?
Dec 24, 2019 22:11:29 GMT -6
ordinaryshaver: You want to use 3 1/2 in magnum lead shot, in size T. Problem solved.
Dec 25, 2019 19:03:30 GMT -6
ordinaryshaver: No steel, too light and use an extra full choke, unless you have a good blind setup
Dec 25, 2019 19:03:54 GMT -6
carlfrommo: Well, last night was a failure. I had one shot, and I didn't lead the red-nosed one enough. I think I ended up shooting the driver. Might have gotten him in the leg. Hard to tell because he was wearing red pants and coat.
Dec 25, 2019 21:31:47 GMT -6
carlfrommo: He turned his sled away and landed on the roof two blocks down. Out of range for a second shot. I did notice he walked with a bit of a limp though. He shouldn't be coming in my yard anyway.
Dec 25, 2019 21:34:48 GMT -6
mrconklin: Last time I hunted waterfowl. 2 3/4 shells were standard and the cool kids were starting to play with the 3 inch, but most guns weren't made for them. Steel was also just starting to be mandated on Federal and State land.
Jan 19, 2020 11:35:39 GMT -6
9nein9: Is it just me or is the site acting wonky?
Jan 23, 2020 0:12:49 GMT -6
9nein9: All good now . Was slow scrolling and freezing up earlier
Jan 23, 2020 1:59:36 GMT -6
ordinaryshaver: No issue on our end, must have been a pro boards issue.
Jan 24, 2020 18:51:19 GMT -6
wchnu: I only see this when I am not in the mobile version.
Jan 29, 2020 18:24:58 GMT -6
ordinaryshaver: Y'all, if y'all only knew what's been going on around my place. Not gone, just have had issues lately.
Feb 5, 2020 15:24:37 GMT -6
ordinaryshaver: If I hadn't gone through it, I couldn't laugh like I do now. All good, and will be back around soon.
Feb 5, 2020 15:25:06 GMT -6
ordinaryshaver: Just got done with 2nd interview with the prospective employer. It went well, so here's to hoping they finish the background check soon. I'll let y'all know when I hear more.
Feb 27, 2020 15:26:47 GMT -6
ordinaryshaver: Starting the new job tomorrow. Going to do the initial paperwork and all that jazz.
Mar 12, 2020 15:40:29 GMT -6
andy914: Congrats on the new job!
Mar 14, 2020 22:44:39 GMT -6