Cold Water Rinse Tea Tree Body Bar Tom's 3D Printed Brush Supply V2 Personna CWR Lilac Vegetal
My prep was just a cold water rinse. The Tea Tree Body Bar face lathered well with Tom's 3D Printed Brush. I did two passes and a cleanup with the Supply V2 razor with a Personna blade and ended up with a close, comfortable shave. After a cold water rinse, I finished off with Lilac Vegetal. I am clean, smooth, and refreshed... The TeaTree Bar did lather well, but the lather is not long lasting. To counter that, it is slick and in no way hindered the shave. I imagine that it is for guys who may shave in the shower. It has a nice scent and a light menthol cooling. It will stay in my Menthol Monday as long as it lasts. I am using it in my showers now.
Gem Jr. Bar Treet super Mer Shavings Barbershop Two band badger.
Quick shave because I slept an hour later than I had planned. I want to try stropping some carbon blades. The treet qas smoother then the Pal carbon o started with and quickly abandoned but not much. However overall it was an enjoyable shave.
Lightly Mentholated Monday RAZOROCK Santa Maria del Fiore has a very nice Tuscan Tabacco Cologne scent with the addition of a small amount of Menthol, Eucalyptus Oil and Camphor
Razor: Ever-Ready 1924 Blade: GEM SS PTFE (9) Soap: RAZOROCK Charcoal-Lime Cube Preshave, RAZOROCK Santa Maria del Fiore Brush: RAZOROCK Monster 26mm A/S: Alum Block, Witch Hazel, RAZOROCK Santa Maria del Fiore Aftershave
The Grosvenor [ 404-mixed ] Vitos Super Red TNNSER 3D Gem S/S [ 1] Jaguar Prestige A/S Lotion
Rather nice to have my own TNNSER thanks to Arthur @ Electrif . This one Shaves just as well as the loaner I sampled, in fact the quality of finish attained equals many of the best that I get with Vintage SE Razors.
Cold Water Rinse Tabac Tom's 3D Printed Brush Supply V2 Personna CWR Tabac AS
My prep was just a cold water rinse. The Tabac Shave Cream face lathered well with Tom's 3D Printed Brush. I did two passes and a cleanup with the Supply V2 razor with a Personna blade and the three dot plate and ended up with a close, comfortable shave. After a cold water rinse, I finished off with Tabac AS. I am clean, smooth, and refreshed...
9nein9: To like or not to like the like button? That is the question. Our society thrives off the like button it seems . I'm not sure if I like it or I don't like it.Just kind of got used to it .
Dec 15, 2019 20:32:06 GMT -6
carlfrommo: Hey guys. Last minute question here. What shot size should I use for flying reindeer?
Dec 24, 2019 22:11:29 GMT -6
ordinaryshaver: You want to use 3 1/2 in magnum lead shot, in size T. Problem solved.
Dec 25, 2019 19:03:30 GMT -6
ordinaryshaver: No steel, too light and use an extra full choke, unless you have a good blind setup
Dec 25, 2019 19:03:54 GMT -6
carlfrommo: Well, last night was a failure. I had one shot, and I didn't lead the red-nosed one enough. I think I ended up shooting the driver. Might have gotten him in the leg. Hard to tell because he was wearing red pants and coat.
Dec 25, 2019 21:31:47 GMT -6
carlfrommo: He turned his sled away and landed on the roof two blocks down. Out of range for a second shot. I did notice he walked with a bit of a limp though. He shouldn't be coming in my yard anyway.
Dec 25, 2019 21:34:48 GMT -6
mrconklin: Last time I hunted waterfowl. 2 3/4 shells were standard and the cool kids were starting to play with the 3 inch, but most guns weren't made for them. Steel was also just starting to be mandated on Federal and State land.
Jan 19, 2020 11:35:39 GMT -6
9nein9: Is it just me or is the site acting wonky?
Jan 23, 2020 0:12:49 GMT -6
9nein9: All good now . Was slow scrolling and freezing up earlier
Jan 23, 2020 1:59:36 GMT -6
ordinaryshaver: No issue on our end, must have been a pro boards issue.
Jan 24, 2020 18:51:19 GMT -6
wchnu: I only see this when I am not in the mobile version.
Jan 29, 2020 18:24:58 GMT -6
ordinaryshaver: Y'all, if y'all only knew what's been going on around my place. Not gone, just have had issues lately.
Feb 5, 2020 15:24:37 GMT -6
ordinaryshaver: If I hadn't gone through it, I couldn't laugh like I do now. All good, and will be back around soon.
Feb 5, 2020 15:25:06 GMT -6
ordinaryshaver: Just got done with 2nd interview with the prospective employer. It went well, so here's to hoping they finish the background check soon. I'll let y'all know when I hear more.
Feb 27, 2020 15:26:47 GMT -6
ordinaryshaver: Starting the new job tomorrow. Going to do the initial paperwork and all that jazz.
Mar 12, 2020 15:40:29 GMT -6
andy914: Congrats on the new job!
Mar 14, 2020 22:44:39 GMT -6